Superglide 1 for Endgame XM1 RGB and XM1r: Fit and Install
By Official Pulsar Gaming Gears - The Best Gaming Gears In the ... | Published: 2026-11-04
Category: How-to Guides
A step-by-step guide to removing old Endgame Gear XM1 skates and fitting Pulsar Superglide 1 glass skates for a smoother, more consistent glide.
Quick answer
To fit Pulsar Superglide 1 skates to your Endgame Gear XM1 RGB or XM1r, remove the original skates with gentle heat, clean the base completely, then align and press each glass skate firmly into its recess. Work slowly and keep the adhesive dry until final placement.
Why preparation matters more than pressure
Glass skates sit flush only when the mouse base is free of old adhesive and debris. Any leftover residue creates a high spot that lifts the skate and causes inconsistent glide. Heat softens the original adhesive so the old skates peel away without tearing fibers from the base.
Unlike curved PTFE feet, Superglide 1 skates are flat glass pads. They do not conform to a dirty surface, so a clean, level base is the difference between a smooth install and a wobbly one.
When to stop and check compatibility
The Superglide 1 is listed specifically for the Endgame Gear XM1 RGB and XM1r. If you own a different XM1 revision, confirm the mounting recess matches before peeling anything. Once original skates are removed, the mouse is not returnable in most cases, so verify the model first.
If your XM1 already has worn or damaged original skates, replacement is sensible. If the originals are intact and you only want a different feel, consider whether the flatter, faster glass surface suits your sensitivity and mousepad before committing.
Step-by-step installation
- Warm the original skates: Use a hair dryer on low heat for 20–30 seconds, holding it 10–15 cm away. Move the heat evenly across each skate. Common mistake: overheating the base, which can soften plastic or loosen internal components. The adhesive should feel tacky, not hot to the touch.
- Peel the old skates slowly: Lift one corner with a plastic tool or your fingernail and pull back at a low angle. Keep the tool flat against the base. Common mistake: prying upward, which can gouge the mouse base or bend the skate. If resistance is high, apply more heat rather than more force.
- Remove all adhesive residue: Dab isopropyl alcohol onto a lint-free cloth and wipe the recess until no sticky film remains. Dry completely. Common mistake: using a wet cloth that leaves moisture trapped under the new skate. The surface must be completely dry and cool before the next step.
- Test-fit before peeling the backing: Place each Superglide 1 skate into its recess without removing the adhesive liner. Check that it sits flush and does not overhang. Common mistake: assuming left and right skates are identical when they may be shaped differently. If a skate does not drop in cleanly, stop and recheck the model compatibility.
- Apply the skates firmly: Peel the backing from one skate, align it with the recess, and press down evenly for 10 seconds. Repeat for the remaining skates. Common mistake: pressing only the center, which leaves edges lifted. Work from the center outward to push out any trapped air.
- Let the adhesive cure: Place the mouse on a clean surface and avoid heavy use for 15–30 minutes. Common mistake: immediately gaming on a dusty mousepad, which can pick up debris before the bond sets. A short cure time reduces the chance of the skate shifting during play.
Product facts
- Superglide 1 for Endgame Gears XM1 RGB / XM1r: Compatible with Endgame Gears XM1 RGB and XM1r mice. This confirms a direct fit for both models, so you can install without trimming or guessing.
Superglide 1 for Endgame Gears XM1 RGB / XM1r - Superglide 1 for Endgame Gears XM1 RGB / XM1r: Part of the Superglide series by Pulsar Gaming Gears, designed to offer a secure grip for improved control. The glass surface is intended to give a consistent, low-friction glide that can improve control during fast swipes.
